Add GPIO beginners guide and fix incorrect API references in libgpiod docs

Documentation/README.md

@@ -31,6 +31,10 @@ While contributing, you should read the [coding guidelines section](https://gith
 
 ### General-Purpose Input/Output (GPIO)
 
+* [GPIO Protocol Guide](./protocols/gpio.md) - Quick start, GpioController usage, and troubleshooting
+* [GPIO Basics](./fundamentals/gpio-basics.md) - Digital I/O concepts, pull resistors, voltage levels
+* [Choosing the Right Driver](./fundamentals/choosing-drivers.md) - LibGpiodDriver vs SysFsDriver comparison
+* [Using libgpiod to control GPIOs](./gpio-linux-libgpiod.md) - libgpiod library versions and installation
 * [GPIO Wiki](https://en.wikipedia.org/wiki/General-purpose_input/output)
 * [Digital I/O Fundamentals](http://www.ni.com/white-paper/3405/en/#toc1)
 

Documentation/fundamentals/choosing-drivers.md

@@ -0,0 +1,168 @@
+# Choosing the Right GPIO Driver
+
+When working with GPIO on Linux systems, .NET IoT offers different driver implementations. This guide helps you understand the differences and choose the right driver for your project.
+
+## Quick Answer
+
+For most users, you do not need to choose a driver at all. The parameterless constructor auto-detects the best driver for your board:
+
+```csharp
+// Recommended — works on all supported boards
+using GpioController controller = new();
+```
+
+Read on if you need to understand what happens under the hood, or if auto-detection does not work for your board.
+
+## Available Drivers
+
+### LibGpiodDriver (Recommended)
+
+Uses the modern `libgpiod` library to access GPIO through the Linux character device interface.
+
+**Use LibGpiodDriver when:**
+
+- Using modern Linux kernels (4.8+)
+- Running on Raspberry Pi OS (Bullseye, Bookworm, or later)
+- Multiple processes may access GPIO simultaneously
+- You want the best-maintained and most future-proof solution
+
+### LibGpiodV2Driver
+
+Same concept as `LibGpiodDriver`, but targets libgpiod version 2.x (the library's API changed between v1 and v2).
+
+**Use LibGpiodV2Driver when:**
+
+- Your system has libgpiod 2.x installed (common on newer distributions)
+
+### SysFsDriver (Deprecated)
+
+Uses the older `/sys/class/gpio` interface, which is deprecated in modern Linux kernels.
+
+**Use SysFsDriver when:**
+
+- Stuck on very old Linux kernels (pre-4.8)
+- **Not recommended for new projects**
+
+## Driver Comparison
+
+| Feature | LibGpiodDriver | SysFsDriver |
+| --- | --- | --- |
+| **Status** | Active, Recommended | Deprecated |
+| **Kernel Version** | 4.8+ | All |
+| **Performance** | Better | Good |
+| **Multi-process** | Safe | Unsafe |
+| **Resource Cleanup** | Automatic | Manual |
+| **Future Support** | Yes | No (being removed) |
+
+## Auto-Detection
+
+When you use `new GpioController()`, the framework automatically selects the best driver:
+
+| Board | Driver selected |
+| --- | --- |
+| Raspberry Pi 3 / 4 | `RaspberryPi3Driver` |
+| Raspberry Pi 5 | `LibGpiodDriver` (with correct GPIO chip) |
+| Other Linux boards | Tries `LibGpiodDriver` → `LibGpiodV2Driver` → `SysFsDriver` |
+
+```csharp
+// Let the framework choose the best driver for your board
+using GpioController controller = new();
+```
+
+## Explicit Driver Selection
+
+If auto-detection does not work, pass a driver to the `GpioController` constructor:
+
+```csharp
+using System.Device.Gpio;
+using System.Device.Gpio.Drivers;
+
+// LibGpiodDriver for libgpiod v1 (chip number 0 on most boards)
+using GpioController controller = new(new LibGpiodDriver(gpioChip: 0));
+
+// LibGpiodV2Driver for libgpiod v2
+using GpioController controller = new(new LibGpiodV2Driver(chipNumber: 0));
+```
+
+### Finding Your Chip Number
+
+Different boards expose GPIO on different chip numbers. Use the `gpioinfo` command to list available chips:
+
+```bash
+gpioinfo
+```
+
+- **Raspberry Pi 3/4:** chip number **0** (`gpiochip0`)
+- **Raspberry Pi 5:** chip number **4** (`gpiochip4`)
+
+## Installing libgpiod
+
+Most Raspberry Pi OS images come with libgpiod pre-installed. If not:
+
+```bash
+sudo apt update
+sudo apt install libgpiod2
+```
+
+To check which version is installed:
+
+```bash
+apt show libgpiod2
+```
+
+For building from source or more detail on library versions, see [Using libgpiod to control GPIOs](../gpio-linux-libgpiod.md).
+
+## Permission Configuration
+
+If you get "Permission denied" errors when accessing GPIO:
+
+```bash
+# Add your user to the gpio group
+sudo usermod -aG gpio $USER
+
+# Log out and log back in, then verify
+groups
+```
+
+## Troubleshooting
+
+### "libgpiod not found" / DllNotFoundException
+
+```bash
+sudo apt install libgpiod2
+```
+
+### Wrong Chip Number (Raspberry Pi 5)
+
+Raspberry Pi 5 uses chip **4** instead of 0. If auto-detection does not work:
+
+```csharp
+using GpioController controller = new(new LibGpiodDriver(gpioChip: 4));
+```
+
+### Driver Version Mismatch
+
+If you get errors, check your installed libgpiod version and use the matching driver class:
+
+- libgpiod 0.x–1.x → `LibGpiodDriver`
+- libgpiod 2.x → `LibGpiodV2Driver`
+
+## Summary
+
+| Situation | What to use |
+| --- | --- |
+| New project, any supported board | `new GpioController()` |
+| Need a specific chip number | `new GpioController(new LibGpiodDriver(gpioChip: N))` |
+| System has libgpiod 2.x only | `new GpioController(new LibGpiodV2Driver(chipNumber: N))` |
+| Very old kernel (pre-4.8) | `new GpioController(new SysFsDriver())` |
+
+## Next Steps
+
+- [GPIO Basics](gpio-basics.md) — Fundamentals of digital I/O, pull resistors, voltage levels
+- [GPIO Protocol Guide](../protocols/gpio.md) — Quick start example and GpioController usage
+- [libgpiod Usage Guide](../gpio-linux-libgpiod.md) — Detailed libgpiod installation and version info
+
+## Additional Resources
+
+- [libgpiod Documentation](https://git.kernel.org/pub/scm/libs/libgpiod/libgpiod.git/about/)
+- [Linux GPIO Documentation](https://www.kernel.org/doc/html/latest/driver-api/gpio/index.html)

Documentation/fundamentals/gpio-basics.md

@@ -0,0 +1,200 @@
+# GPIO Basics
+
+General-Purpose Input/Output (GPIO) pins are the foundation of IoT hardware interfacing. They are programmable electrical pins on single-board computers like the Raspberry Pi that let your .NET code interact with physical hardware — turning LEDs on and off, reading button presses, and communicating with sensors.
+
+This guide explains the essential concepts you need to understand when working with GPIO pins in .NET IoT.
+
+## What is GPIO?
+
+GPIO pins are programmable pins on your single-board computer that can:
+
+- **Output digital signals** — Turn devices on/off (LEDs, relays, motors)
+- **Read digital signals** — Detect button presses, sensor states
+- **Generate PWM signals** — Control brightness, speed (requires specific PWM-capable pins)
+- **Communicate via protocols** — I2C, SPI, UART (requires specific pins)
+
+GPIO pins operate with digital logic levels (HIGH/LOW):
+
+- **HIGH** = 3.3 V on Raspberry Pi (varies by platform)
+- **LOW** = 0 V (Ground)
+
+## Pin Numbering
+
+There are two ways to refer to pins, which can be confusing at first:
+
+| Scheme | Example | Description |
+| --- | --- | --- |
+| **GPIO / BCM** | `18` | The number used by the Broadcom chip — **this is what .NET IoT uses** |
+| **Physical / Board** | `12` | The physical position on the 40-pin header |
+
+GPIO 18 and physical pin 12 are the **same pin** — just identified differently. Your code always uses **GPIO (BCM) numbers**.
+
+Use the interactive diagram at [pinout.xyz](https://pinout.xyz/) to look up the mapping for your board.
+
+## Digital Output
+
+Digital output means setting a pin to either HIGH (3.3 V) or LOW (0 V). That is all digital output does: voltage on or voltage off.
+
+```csharp
+using System.Device.Gpio;
+
+using GpioController controller = new();
+controller.OpenPin(18, PinMode.Output);
+
+controller.Write(18, PinValue.High); // 3.3 V — turns the LED on
+controller.Write(18, PinValue.Low);  // 0 V   — turns the LED off
+```
+
+You can use this to drive LEDs, buzzers, relays, and any component that responds to a high/low signal.
+
+### Driving an LED
+
+LEDs require a current-limiting resistor to prevent damage:
+
+```text
+GPIO Pin ──► LED (Anode/+) ──► LED (Cathode/−) ──► Resistor (220 Ω) ──► Ground
+```
+
+> **Why a resistor?** LEDs need very little current. Without a resistor, the LED draws too much current and can burn out or damage your Pi. A 220 Ω resistor limits the current to a safe level (~6 mA).
+
+## Digital Input
+
+Digital input means reading whether a pin is HIGH or LOW.
+
+```csharp
+using System.Device.Gpio;
+
+using GpioController controller = new();
+controller.OpenPin(17, PinMode.InputPullUp);
+
+PinValue value = controller.Read(17);
+if (value == PinValue.Low)
+{
+    Console.WriteLine("Button is pressed!");
+}
+```
+
+### Pull-Up and Pull-Down Resistors
+
+When a button is **not** pressed, the pin is not connected to anything. In plain `Input` mode, this leaves the pin "floating" — its voltage drifts randomly, giving unreliable readings.
+
+Pull-up and pull-down resistors solve this by defining a default voltage:
+
+| Mode | Default state (not pressed) | Pressed state | Wiring |
+| --- | --- | --- | --- |
+| `InputPullUp` | High (3.3 V) | Low (0 V) | Button connects pin to Ground |
+| `InputPullDown` | Low (0 V) | High (3.3 V) | Button connects pin to 3.3 V |
+
+`InputPullUp` is the most common choice for buttons. The Raspberry Pi has built-in pull-up resistors that are activated when you use this mode — no external resistor required.
+
+```csharp
+controller.OpenPin(17, PinMode.InputPullUp);
+
+// When button is NOT pressed: reads HIGH
+// When button IS pressed: reads LOW (inverted logic)
+if (controller.Read(17) == PinValue.Low)
+{
+    Console.WriteLine("Button pressed");
+}
+```
+
+### Button Wiring (with InputPullUp)
+
+```text
+GPIO 17 ──► one leg of button
+GND     ──► other leg of button
+```
+
+When the button is pressed, GPIO 17 gets connected to Ground (Low). When released, the internal pull-up resistor pulls it back to High.
+
+## Interrupt-Driven Input (Events)
+
+Instead of checking the pin over and over in a loop (polling), you can register a callback that fires when the pin's value changes. This is more efficient and more responsive:
+
+```csharp
+using System.Device.Gpio;
+
+using GpioController controller = new();
+controller.OpenPin(17, PinMode.InputPullUp);
+
+controller.RegisterCallbackForPinValueChangedEvent(
+    17,
+    PinEventTypes.Falling, // trigger on button press (HIGH → LOW)
+    (sender, args) =>
+    {
+        Console.WriteLine($"Button pressed on pin {args.PinNumber}");
+    });
+
+Console.WriteLine("Press the button. Ctrl+C to exit.");
+Thread.Sleep(Timeout.Infinite);
+```
+
+**Event types:**
+
+- `PinEventTypes.Rising` — LOW → HIGH transition
+- `PinEventTypes.Falling` — HIGH → LOW transition
+- `PinEventTypes.Rising | PinEventTypes.Falling` — both directions
+
+> **Note:** Physical buttons "bounce" — a single press can generate several rapid transitions. If you experience duplicate button events, you need debouncing. A simple approach is to ignore events that arrive within a short time window (e.g., 50 ms) of the previous event.
+
+## Current and Voltage Limitations
+
+### Raspberry Pi GPIO Specifications
+
+- **Output Voltage:** 3.3 V (not 5 V!)
+- **Max current per pin:** ~16 mA (safe limit)
+- **Max total current (all pins):** ~50 mA
+- **Input voltage tolerance:** 0 V to 3.3 V (**5 V will damage the pin!**)
+
+### Connecting 5 V Devices
+
+**Never connect 5 V signals directly to GPIO pins!** Use one of these solutions:
+
+1. **Voltage divider** (for input signals)
+2. **Level shifter** (bidirectional, for I2C/SPI)
+3. **Transistor/MOSFET** (for high-current outputs)
+
+### Driving High-Current Devices
+
+For loads exceeding 16 mA (motors, relays, high-power LEDs), use a transistor or MOSFET as a switch powered from an external supply. The GPIO pin controls the transistor's gate, not the device directly.
+
+## Pin Mode Summary
+
+| PinMode | Description | Typical Use |
+| --- | --- | --- |
+| `Output` | Drive pin HIGH or LOW | LEDs, control signals |
+| `Input` | Read pin state (floating) | Rarely used |
+| `InputPullUp` | Read pin, default HIGH | Buttons (active-low) |
+| `InputPullDown` | Read pin, default LOW | Sensors (active-high) |
+
+## Common GPIO Pins on Raspberry Pi
+
+Not all GPIO pins are suitable for general use:
+
+- **GPIO 2, 3:** I2C (have hardware pull-up resistors)
+- **GPIO 14, 15:** UART (default serial console)
+- **GPIO 9, 10, 11:** SPI
+- **GPIO 18, 19:** PWM-capable
+- **Safe for general use:** 17, 22, 23, 24, 25, 27
+
+**Tip:** Check your specific Raspberry Pi model's pinout at [pinout.xyz](https://pinout.xyz/).
+
+## Best Practices
+
+1. **Always dispose of GpioController** — Use `using` statements or call `.Dispose()`
+2. **Use `InputPullUp` or `InputPullDown`** — Never leave input pins floating
+3. **Respect voltage levels** — Raspberry Pi GPIO operates at 3.3 V; connecting 5 V **will damage the pin**
+4. **Use resistors with LEDs** — Calculate the value or use 220 Ω as a safe default
+5. **Check pin assignments** — Some GPIO pins are shared with I2C, SPI, or UART; using them for general GPIO disables those interfaces
+6. **Document your pin usage** — Especially in projects using multiple pins
+
+## Next Steps
+
+- [GPIO Protocol Guide](../protocols/gpio.md) — Quick start, GpioController usage, drivers, and troubleshooting
+- [Choosing the Right Driver](choosing-drivers.md) — LibGpiodDriver vs SysFsDriver comparison
+
+## Additional Resources
+
+- [GPIO Wikipedia](https://en.wikipedia.org/wiki/General-purpose_input/output)
+- [Raspberry Pi GPIO Pinout](https://pinout.xyz/)
+- [Digital I/O Fundamentals](http://www.ni.com/white-paper/3405/en/#toc1)